2.2 ho intake mani question!!!
#1
Member
Thread Starter
Join Date: 09-26-07
Location: Talbot Co. Maryland
Posts: 354
Likes: 0
Received 0 Likes
on
0 Posts
2.2 ho intake mani question!!!
has anyone noticed once they put theres on a slight clicking noise and it didnt have a valve tap before i put it on there??? im real sketch now guys could it be becuase the mani is thinner or something i dunno
#3
Member
Thread Starter
Join Date: 09-26-07
Location: Talbot Co. Maryland
Posts: 354
Likes: 0
Received 0 Likes
on
0 Posts
i know i didnt have a prob i just managed to notice a faint ticking over the injectoers that was louder then normal and i noticed a HUGE gain because i used to chirp third now i spin into third!!!
#6
Intake
ported TB
2.4 intake manifold
ported intake ports
Ported exhaust manifold
catless DP
LSJ resonator
full 2.25 exhaust
and the knowledge of my car AKA driver mod .im 5 speed of course.The 15.40 run was without porting and 2.4 mani and a diff exhaust setup.so well see what happens
ported TB
2.4 intake manifold
ported intake ports
Ported exhaust manifold
catless DP
LSJ resonator
full 2.25 exhaust
and the knowledge of my car AKA driver mod .im 5 speed of course.The 15.40 run was without porting and 2.4 mani and a diff exhaust setup.so well see what happens
#7
Member
Thread Starter
Join Date: 09-26-07
Location: Talbot Co. Maryland
Posts: 354
Likes: 0
Received 0 Likes
on
0 Posts
nice man u may break 14's with all that **** haha
i just hope that little ticking noise is just the manifold!!! because im wiggin out haha i mean it runs fine and purs like a kitten and it just bothers me becuase i dont know what that noise is!!!
i just hope that little ticking noise is just the manifold!!! because im wiggin out haha i mean it runs fine and purs like a kitten and it just bothers me becuase i dont know what that noise is!!!
#8
mmm i doubt it.Im still on stock mounts and a newer stock clutch.Ill be suprised if I get a 15.1 but I need to hit up the track and see what I can pull out of her.as soon as she's fully bolted on and toon'd im gonna put a 75 shot on her
#11
Senior Member
Join Date: 09-25-08
Location: Depew, NY
Posts: 5,384
Likes: 0
Received 0 Likes
on
0 Posts
Fully release the clutch before adding throttle. Your clutch hates you.
#17
Member
Thread Starter
Join Date: 09-26-07
Location: Talbot Co. Maryland
Posts: 354
Likes: 0
Received 0 Likes
on
0 Posts
huh wierd im not to worried about it because its still runnin hard and strong so i mean i put my header on yesterday and it felt like it kinda took power from what i had with the stock exhaust mani on it wtf? ha
#18
Senior Member
Join Date: 05-07-07
Location: Rochester, NY
Posts: 1,847
Likes: 0
Received 0 Likes
on
0 Posts
you shifted your powerband up, you'll lose a lot of low end torque by switching to 2.4intake manifold and larger exhaust
#20
Member
iTrader: (1)
Join Date: 05-02-08
Location: baltimore
Posts: 292
Likes: 0
Received 0 Likes
on
0 Posts
yeah i lost most of my mid range when i switched to a 2.4 mani i almost dont think its worth it. my colby used to chirp 2nd hard now its hard to chirp second. i dont know how you guys are getting such low 1/4 times best i ran with cat back 2.4 and intake was 16.2 in a sedan
#22
Member
Thread Starter
Join Date: 09-26-07
Location: Talbot Co. Maryland
Posts: 354
Likes: 0
Received 0 Likes
on
0 Posts
wow man im not sure but the humidity i know over here is killin my car becuase its so sluggish when it gets around 70-80 and when the humidity goes away shes got enough pull to move the earth haha
well i banged out a gti VR6 by 4 cars when i had just intake exhaust and shortshift so i wonder how bad i will rape him this time becuase he wants to race me again haha
well i banged out a gti VR6 by 4 cars when i had just intake exhaust and shortshift so i wonder how bad i will rape him this time becuase he wants to race me again haha
Last edited by SpeedJunkies07LS; 06-11-2009 at 04:03 PM. Reason: Automerged Doublepost
#24
#25
Senior Member
Join Date: 05-07-07
Location: Rochester, NY
Posts: 1,847
Likes: 0
Received 0 Likes
on
0 Posts