Cobalt SS Network

2.2L L61 Performance Tech 16 valve 145 hp EcoTec with 155 lb-ft of torque

Help!!!!!

Thread Tools
 
Search this Thread
 
Old 04-17-2011, 05:54 PM
  #1  
New Member
Thread Starter
 
cobraceralt's Avatar
 
Join Date: 07-25-09
Location: brighton,co
Posts: 146
Likes: 0
Received 0 Likes on 0 Posts
Help!!!!!
i installed the 2.4 IM and i installed everything correctly hooked up the MAP sensor and when i started it up my idle is now between 3100-3600 how can i adjust that or is it through tune only? or DID i install something incorrectly?
cobraceralt is offline  
Reply Like
Old 04-17-2011, 07:18 PM
  #2  
New Member
Thread Starter
 
cobraceralt's Avatar
 
Join Date: 07-25-09
Location: brighton,co
Posts: 146
Likes: 0
Received 0 Likes on 0 Posts
bump?
cobraceralt is offline  
Reply Like
Old 04-17-2011, 07:57 PM
  #3  
New Member
Thread Starter
 
cobraceralt's Avatar
 
Join Date: 07-25-09
Location: brighton,co
Posts: 146
Likes: 0
Received 0 Likes on 0 Posts
come one guys i need some help you can read it so you can post some help so bump?
cobraceralt is offline  
Reply Like
Old 04-17-2011, 07:59 PM
  #4  
Senior Member
iTrader: (4)
 
Turbalt2010's Avatar
 
Join Date: 05-13-10
Location: New York
Posts: 1,427
Likes: 0
Received 0 Likes on 0 Posts
im no help, sorry. bump
Turbalt2010 is offline  
Reply Like
Old 04-17-2011, 08:54 PM
  #5  
Former Vendor
iTrader: (24)
 
TurboTechRacing's Avatar
 
Join Date: 01-28-05
Location: On Here
Posts: 13,714
Received 40 Likes on 34 Posts
Did you hook up everything? Sounds like maybe a vaccum leak? Extra air will cause a high idle.
TurboTechRacing is offline  
Reply Like
Old 04-17-2011, 08:55 PM
  #6  
New Member
Thread Starter
 
cobraceralt's Avatar
 
Join Date: 07-25-09
Location: brighton,co
Posts: 146
Likes: 0
Received 0 Likes on 0 Posts
Originally Posted by Turbalt2010
im no help, sorry. bump
thank you for atleast acknowledging lol
cobraceralt is offline  
Reply Like
Old 04-17-2011, 09:06 PM
  #7  
Senior Member
iTrader: (6)
 
ECaulk's Avatar
 
Join Date: 07-19-10
Location: Houston, Texas
Posts: 26,596
Received 840 Likes on 737 Posts
its most likely a vacuum leak or you didnt get a gasket seated right. you did unhook your battery while you did the install?
ECaulk is offline  
Reply Like
Old 04-17-2011, 09:09 PM
  #8  
Former Vendor
iTrader: (24)
 
TurboTechRacing's Avatar
 
Join Date: 01-28-05
Location: On Here
Posts: 13,714
Received 40 Likes on 34 Posts
Originally Posted by blackonblack07
its most likely a vacuum leak or you didnt get a gasket seated right. you did unhook your battery while you did the install?
Glas you agree
TurboTechRacing is offline  
Reply Like
Old 04-17-2011, 09:14 PM
  #9  
Senior Member
iTrader: (12)
 
kxrida2000's Avatar
 
Join Date: 09-14-09
Location: Pittsburgh
Posts: 4,128
Likes: 0
Received 1 Like on 1 Post
like others stated its a vacuum leak
kxrida2000 is offline  
Reply Like
Old 04-17-2011, 09:31 PM
  #10  
Senior Member
 
NJHK's Avatar
 
Join Date: 01-05-06
Location: East Brunswick, NJ
Posts: 10,877
Likes: 0
Received 2 Likes on 2 Posts
Did you disconnect your idle air controller?
NJHK is offline  
Reply Like
Old 04-17-2011, 10:01 PM
  #11  
New Member
Thread Starter
 
cobraceralt's Avatar
 
Join Date: 07-25-09
Location: brighton,co
Posts: 146
Likes: 0
Received 0 Likes on 0 Posts
i have figured it out i think. no pcv seal or from what ive read also known as crankcase breather seal. i was not aware of this and apparently did not install it im going to a dealer tomorrow to pick one up and pray to allah that it works cus this high idle **** sucks! lol. and i did not disconnect my battery during instal but i did do so after complete installation
cobraceralt is offline  
Reply Like
Back to Subforum
2.2L L61 Performance Tech
View Next Unread
SAI tricky?




Advanced Search

All times are GMT -4. The time now is 12:33 PM.