jet module problems
#1
New Member
Thread Starter
Join Date: 05-23-08
Location: edmonton,ab
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
jet module problems
my stage 2 module is trying to engage my clutch and im wondering if anyone else is having this problem. do i need tuning or a tech 2 program to trouble shoot this problem. i installed it on a rental car and it worked but in my car no dice.
#2
Senior Member
Join Date: 06-18-06
Location: Madison,WI
Posts: 4,883
Likes: 0
Received 0 Likes
on
0 Posts
um that makes no since how this piggy back type computer modification would in some way mess with a hydrolic clutch system
im trying to think of what electronic things would be on that system but i think its a very mechanical system
im trying to think of what electronic things would be on that system but i think its a very mechanical system
#3
New Member
Thread Starter
Join Date: 05-23-08
Location: edmonton,ab
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
i know it is fine at first but after three stop and starts i take it out of gear and hold the clutch in it still jerks forward and stalls. but my cobalt came with an ss dash kit so would it be possible that i have miss matched parts?-from factory
#11
New Member
Thread Starter
Join Date: 05-23-08
Location: edmonton,ab
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
the chip works wicked when it is workin but im going to reinstall today after work to refreash my memory but it could also be somthing with the idle because it goes from 500rpm to almost zero then jumps up to2500 then wile comin down the car stalls.
my dash had the silver ss inserts in it when i bought it and w/out mods went like hell
my dash had the silver ss inserts in it when i bought it and w/out mods went like hell
Last edited by dem boyz; 06-12-2008 at 02:24 PM. Reason: Automerged Doublepost
#16
Senior Member
that is a bad slave cylinder, most likely.
whats happeneing is, when the RPM goes up, it can't hold the spring in,a nd the clutch is engaging.
mine is also bad, and it rides fine under 3000 rpm, once it goes up, can't shift.
whats happeneing is, when the RPM goes up, it can't hold the spring in,a nd the clutch is engaging.
mine is also bad, and it rides fine under 3000 rpm, once it goes up, can't shift.
#17
odd that RPM's affect you gear changes. With a leaky slave the only thing that shiould affect anything at all would be amount of time clutch pedal is held down. The slave fails due to fluid leaking/bleeding past a seal so the longer the pedal is held down, the more fluid is leaked. RPM's "should" not affect that really but i may be wrong >.<
#18
Senior Member
Join Date: 12-21-07
Location: lucedale, ms
Posts: 3,741
Likes: 0
Received 0 Likes
on
0 Posts
man have ya'll not read what he said.. he said it jerked foward with the clutch engaged and out of gear.. how the **** can that be possible at all??? its not..
#19
Senior Member
odd that RPM's affect you gear changes. With a leaky slave the only thing that shiould affect anything at all would be amount of time clutch pedal is held down. The slave fails due to fluid leaking/bleeding past a seal so the longer the pedal is held down, the more fluid is leaked. RPM's "should" not affect that really but i may be wrong >.<
long story short, it's a shitty aftermarket cylinder that came with my clutch kit. it's the only part that wasn't replaced after it started acting up.
#20
OHHHH lol i didnt get at what you were saying. Totally skipped past that whole "out of gear" thing. Aside from poor cable adjustment (possible shifter replacement?) that is impossible good catch man
#21
Senior Member
that's a good point, or perhaps something is damaged in the shift assembly on the trans.
#22
Yah. Only way you canbe sure of anything is to remove so called "Jet chip" and see if problem persists. If you remove part and the symptom is gone its pretty safe to say this chip is garbage
#23
New Member
Thread Starter
Join Date: 05-23-08
Location: edmonton,ab
Posts: 14
Likes: 0
Received 0 Likes
on
0 Posts
my engine is fine , my dash had a ss badge on it and the chip is working better gm mechanic says i need to do somemore tuning because my computer has a funny glitch and it has to be programmed out because he says its trying to think like an automatic. if this does nothing its going back to jet.