Drivetrain: How To: Clutch Job on Cobalt SS
02-20-2012 | 02:55 PM
#1
How To: Clutch Job on Cobalt SS
I hope this helps someone. I know I would have liked to have this when researching what I needed to do mine. I did the write up in PDF form so I will link it here.
Thanks goes to James (Chevycobaltss3) and Nick (ccrunner84).
https://app.box.com/shared/35cb5d8e1179737b6a45
http://frogstofall.f3h.com/Clutch%20...obalt%20SS.pdf
Thanks goes to James (Chevycobaltss3) and Nick (ccrunner84).
https://app.box.com/shared/35cb5d8e1179737b6a45
http://frogstofall.f3h.com/Clutch%20...obalt%20SS.pdf
Last edited by riceburner; 12-08-2014 at 03:50 PM.
02-20-2012 | 08:19 PM
#4
Proper way to bleed clutch on these is to apply vacuum to reservior and works alot faster and easier.
Hydraulic Clutch System Bleeding
Special Tools
•
J-35555 Metal Mityvac
•
J 43485 Power Steering Bleeder Adapter
1.
Verify that all the lines and fittings are dry and secure.
2.
Clean the dirt and grease from the reservoir cap in order to ensure that no foreign substances enter the system.
3.
Remove the reservoir cap.
4.
Fill the reservoir to the proper level with the required fluid.
Some manual transmission equipped vehicles have a combined brake and clutch fluid reservoir.
5.
Attach the J 43485 power steering bleeder adapter to the J-35555 Metal Mityvac, or equivalent.
Note: Brake fluid will deteriorate the rubber on the J 43485 power steering bleeder adapter. Use a clean shop cloth to wipe away the fluid after each use.
6.
Place and hold the adapter on the reservoir filler neck to ensure a tight fit. In some cases, the adapter will fit into the reservoir opening.
7.
Apply a vacuum of 51–68 kPa (15–20 hg) and remove the adapter.
8.
Refill the reservoir to the proper level.
9.
Repeat steps 6 and 7.
10.
If needed, refill the reservoir and continue to pull a vacuum until no more bubbles can be seen in the reservoir or until the fluid level no longer drops.
Warning: The vehicle will move if started in gear before the Actuator Cylinder is refilled and operational. Start the vehicle the first time in neutral to help prevent personal injury from vehicle movement and see if the transmission will shift easily into gear.
11.
Pump the clutch pedal until firm (to refill actuator cylinder).
12.
Add additional fluid if needed.
13.
Test drive the vehicle to ensure proper operation.
Hydraulic Clutch System Bleeding
Special Tools
•
J-35555 Metal Mityvac
•
J 43485 Power Steering Bleeder Adapter
1.
Verify that all the lines and fittings are dry and secure.
2.
Clean the dirt and grease from the reservoir cap in order to ensure that no foreign substances enter the system.
3.
Remove the reservoir cap.
4.
Fill the reservoir to the proper level with the required fluid.
Some manual transmission equipped vehicles have a combined brake and clutch fluid reservoir.
5.
Attach the J 43485 power steering bleeder adapter to the J-35555 Metal Mityvac, or equivalent.
Note: Brake fluid will deteriorate the rubber on the J 43485 power steering bleeder adapter. Use a clean shop cloth to wipe away the fluid after each use.
6.
Place and hold the adapter on the reservoir filler neck to ensure a tight fit. In some cases, the adapter will fit into the reservoir opening.
7.
Apply a vacuum of 51–68 kPa (15–20 hg) and remove the adapter.
8.
Refill the reservoir to the proper level.
9.
Repeat steps 6 and 7.
10.
If needed, refill the reservoir and continue to pull a vacuum until no more bubbles can be seen in the reservoir or until the fluid level no longer drops.
Warning: The vehicle will move if started in gear before the Actuator Cylinder is refilled and operational. Start the vehicle the first time in neutral to help prevent personal injury from vehicle movement and see if the transmission will shift easily into gear.
11.
Pump the clutch pedal until firm (to refill actuator cylinder).
12.
Add additional fluid if needed.
13.
Test drive the vehicle to ensure proper operation.
02-20-2012 | 11:09 PM
#6
Ditto. It didn't seem to do anything when doing the vac first.
02-20-2012 | 11:14 PM
#7
02-20-2012 | 11:21 PM
#8
02-27-2012 | 09:23 PM
#19
02-27-2012 | 10:33 PM
#22
Senior Member
Joined: 06-22-09
Posts: 5,989
Likes: 6
From: Kathmandu
AWESOME!! You guys are my new heroes. I was talking to interviewatruins about doing this job ourselves on our cars. I have everything except the vac bleeder, which I still don't understand. Do you guys have any pics of that part?
02-27-2012 | 10:43 PM
#23
Are you guys doing the vac bleeder process correctly? I bleed all my clutches like that and they come out perfect with no drama. It takes 3-4 cycles as per the instructions, first couple times it feels like nothing changed, then all of a sudden you will have a nice normal pedal with no mess. I set it up while i'm putting back the final parts and let it bleed while i'm working, then go drive the car. Easy as pie.
