Official: Minnesota Chat 2012
#276
Senior Member
Join Date: 10-10-10
Location: Eagan, MN
Posts: 1,852
Likes: 0
Received 0 Likes
on
0 Posts
Got a delco temp sensor. Gonna hold off on the knock sensor until I know its actually the knock sensor that's bad or just because my car starts up like its being choked all to hell
#277
Senior Member
Join Date: 10-10-10
Location: Eagan, MN
Posts: 1,852
Likes: 0
Received 0 Likes
on
0 Posts
temp sensor in. i didn't realize you could fit a damn deepwell over that stupid thing. woulda cut my time from 45 mins to about 5 if i did it that way. works now. no CEL yet because i had to disco the battery, but we will see
#278
Senior Member
Join Date: 11-25-07
Location: St.Paul minnesnowta
Posts: 2,966
Likes: 0
Received 0 Likes
on
0 Posts
#279
Senior Member
Join Date: 10-10-10
Location: Eagan, MN
Posts: 1,852
Likes: 0
Received 0 Likes
on
0 Posts
yea. the reason it was choking was because it was putting in too much fuel, thinking it was cold even though it was already warm. same thing happened the last time the temp sensor went out. so i basically flooded it. felt like a jackass ricer next to an SRT4 earlier because the car didn't wanna start and then it jumped to 2k once it finally did after 3 tries ><
#281
Senior Member
lol i bet she pulls good!
well i have been stock up until this week.
i hve a K&N sri,hahn DP,Hahn Cat-back and a custom made IC piping.
GMS1 will be here tomorrow,so ill be headed to the dealership to get reflashed. i got bored and put the cat back on,on monday lol
everything else is still off the car...until this weekend lol. yea yea,i know i shoulda got a custom tune but i need my warranty to hold up! lol
well i have been stock up until this week.
i hve a K&N sri,hahn DP,Hahn Cat-back and a custom made IC piping.
GMS1 will be here tomorrow,so ill be headed to the dealership to get reflashed. i got bored and put the cat back on,on monday lol
everything else is still off the car...until this weekend lol. yea yea,i know i shoulda got a custom tune but i need my warranty to hold up! lol
#282
Senior Member
Join Date: 10-10-10
Location: Eagan, MN
Posts: 1,852
Likes: 0
Received 0 Likes
on
0 Posts
went to oreilly and checked my codes again... kind of weird... i have 1 pending p0121 and one solid p0121... literally brought up two of the same code... thoughts?
also... bought a clutch ><
also... bought a clutch ><
#283
Senior Member
Join Date: 06-11-07
Location: Minnesota
Posts: 885
Likes: 0
Received 0 Likes
on
0 Posts
Are you still coming up thursday so I can look at the damn thing?
#285
Senior Member
iTrader: (1)
Po121 is a two trip code. if it detects the problem after one trip itll be pending, after two is a solid, UNTIL it see's something like 50 start up without the fault. if it see's the fault again during this time, it'll throw another pending...
Are you still coming up thursday so I can look at the damn thing?
Are you still coming up thursday so I can look at the damn thing?
#287
Senior Member
Join Date: 10-10-10
Location: Eagan, MN
Posts: 1,852
Likes: 0
Received 0 Likes
on
0 Posts
he's gonna double check my wiring since i'm throwing that stupid code
OH also, i'm trying to get a cruise together on sunday. anyone in?
OH also, i'm trying to get a cruise together on sunday. anyone in?
Last edited by BankerBalt; 03-13-2012 at 09:43 AM. Reason: Automerged Doublepost
#289
Senior Member
#292
Senior Member
Join Date: 11-25-07
Location: St.Paul minnesnowta
Posts: 2,966
Likes: 0
Received 0 Likes
on
0 Posts
i will probably be hung over on sunday so i prolly wont be down for a cruise lol but then again i might not woop it up like i did last year. god damn bars are spendy on St.pattys day!
#300
Senior Member
Join Date: 06-28-06
Location: Rochester, mn
Posts: 6,651
Likes: 0
Received 0 Likes
on
0 Posts
speaking of not fun stuff... what in the hell would cause your bolts to start tightening and grinding into the pulley?
the odd bolt out is the same length and thread, but could that have caused it (i stripped the other out and haven't gotten replacements)? My belt is slightly out of alignment as well.
the odd bolt out is the same length and thread, but could that have caused it (i stripped the other out and haven't gotten replacements)? My belt is slightly out of alignment as well.