Mark this thread as Unsold
For Sale 2006 cobalt lt turbo kit for sale. tampa
#1
Member
Thread Starter
Join Date: 02-17-10
Location: tampa
Posts: 249
Likes: 0
Received 0 Likes
on
0 Posts
2006 cobalt lt turbo kit for sale. tampa
going back to stock as i have other priorities right now. this is the complete bolt on kit made by me minus tuning. trifecta tuned it for 25psi but i have only been running 10psi till i could build the motor which is now not going to happen. unfortunetly tuning is vin specific so tuning will be required. i will need some stock parts in return my car back to driveable condition. prefer local transaction as shipping will get pricey. turbo kit has ~500 miles on it and performs flawlessly. i designed it to be a sleeper and from the outside you cant tell its turbocharged. 3000.00 for all of it.
what your getting in the kit:
stainless log manifold
gt35(journal bearing turbo with 2.5 v band downpipe flange(garrett knock off)
turbo exhaust housing heat wrap
38mm external wastegate set at 10 psi
2.5 v band downpipe wrapped with heat wrap(two o2 bungs welded on it for ecm o2 and wideband o2)
oil feed line with .060 restrictor (will need to drill and tap a 1/8npt hole in the oil filter housing)
-8 oil drain line (will need to drill oil pan above oil drain plug)
2.5" free flowing cat convertor(post cat o2 bung welded on)
2.5" cat back exhaust(made by me from aluminized steel and 2.5 v band clamps) with a 2.5" stainless canister with burnt blue tip
all boost piping with maf bung
loud v band bov
intercooler
vacuum lines
two gauge a piller gauge pod
autometer vacuum and 30 psi electronic boost gauge(not a mechanical gauge)
autometer wideband o2
4 seimens 80# injectors
4 pulstar spark plugs
visit link for pics
cobalt turbo pictures by haya262000 - Photobucket
i will need the following parts in exchange to be able to drive my vehicle after turbo kit sells.
stock airbox assembly
complete exhaust system from manifold to muffler
what your getting in the kit:
stainless log manifold
gt35(journal bearing turbo with 2.5 v band downpipe flange(garrett knock off)
turbo exhaust housing heat wrap
38mm external wastegate set at 10 psi
2.5 v band downpipe wrapped with heat wrap(two o2 bungs welded on it for ecm o2 and wideband o2)
oil feed line with .060 restrictor (will need to drill and tap a 1/8npt hole in the oil filter housing)
-8 oil drain line (will need to drill oil pan above oil drain plug)
2.5" free flowing cat convertor(post cat o2 bung welded on)
2.5" cat back exhaust(made by me from aluminized steel and 2.5 v band clamps) with a 2.5" stainless canister with burnt blue tip
all boost piping with maf bung
loud v band bov
intercooler
vacuum lines
two gauge a piller gauge pod
autometer vacuum and 30 psi electronic boost gauge(not a mechanical gauge)
autometer wideband o2
4 seimens 80# injectors
4 pulstar spark plugs
visit link for pics
cobalt turbo pictures by haya262000 - Photobucket
i will need the following parts in exchange to be able to drive my vehicle after turbo kit sells.
stock airbox assembly
complete exhaust system from manifold to muffler
#7
Member
Thread Starter
Join Date: 02-17-10
Location: tampa
Posts: 249
Likes: 0
Received 0 Likes
on
0 Posts
ive built many turbo cars and motorcycles with these turbos and havent had one failure. if your not interested, then dont reply. most turbo failures are caused by builder error.
#8
Senior Member
iTrader: (6)
Join Date: 07-24-09
Location: Lewisburg, Pa
Posts: 1,680
Likes: 0
Received 0 Likes
on
0 Posts
Dude really? The first turbo I had was an ebay 60 trim and the thing was an animal. Have you ever seen dayta's car or his videos on the dyno? Ebay turbo...I wish I would have never let that thing go it killed my 3076r up top. So don't talk unless you know, especially in someone's for sale thread. Common courtesy I think
Thread
Thread Starter
Forum
Replies
Last Post
Josh@ottp
Supporting Vendor Deals & Group Purchases
0
09-08-2015 10:18 AM