1LowLS

Nice!I love Hondas that are properly done.

Fitz88

me too! a couple of my friends' cars have been in honda tuning magazine...theyre not exactly cut springs and a fart can lol

1LowLS

Haha so true.His teg has a flowmaster on it and some Tokico setup.Sounds really good for a flowmaster haha

Fitz88

interesting, never heard a flowmaster on one before. i know a kid with a stanced integra and he used to have a buddy club exhaust. omg was it loudd lol

1LowLS

yeah it's def different,but it's not obnoxious or ricey.

07cobaltLScoupe

meh. only reason there is wheel gap yet is because i'm on 15's, these same wheels in 17's would look sick right now i have about 4" of clearance under the front valence

Fitz88

time for new wheels!

07cobaltLScoupe

nah man, i love how these look with my car even if they are 15's i can't justify spending money on new wheels/tires right now, just trying to keep up on maintenance with the car. only reason i got coils was because the front struts were starting to go, and now i may need to get at least 1 new axle because of what i said in 1 of my previous posts. if that starts leaking again i dont know if i should just get a cheap replacement axle or go with ZZP stage 1 2.2/2.4 axles, and then it makes me think should i look into powell 2.2 rotated trans mounts as well. one thing always leads to another

Brags

Just go stock axels, the bearing on my zzps lasted a week lol, they said they would replace, but selling car anyway. im back on stock with 341 whp and there fine. rotated mounts would def help

07cbaltLS

I'm looking for a black LS that had a front lip installed on it. It almost looked like a home depot special, but I can't remember if it was that, a one off project or if it was aftermarket, but I know it was in here. I've looked through probably 75 or so pages between last night and today and I can't find it. Saw it maybe 6 months ago in here. Anybody know which one it is?

Tundraboarder666

1lowls had a homedepot lipp for a while...

1LowLS

Yeah buddy

07cobaltLScoupe

thanks for the heads up, right now the "fix" is holding well so i should (fingers crossed) be good for a while.

Fitz88

probly thinking of slick54?

rcarr0327

iTrader: (1)

whoa whoa whoa, brags. youre selling your car?!

Brags

Unfortunately yes. Need something a little more useful, maybe grand cherokee with hemi. It wouldn't cost that much more than engine\head build for you

rcarr0327

iTrader: (1)

lolol, well good luck with that man. the cobalt will be missed!

on a side note, anyone know how to replace lash adjusters. im about to buy some but need a little more insight on how to replace them. i heard that you can just loosen the rockers or even loosen the cam caps and squeeze them out. anyone? thanks

1LowLS

Easiest/safest way is to pull the side cover,pull the cams and have full access to them.Then re time the motor.If you try to do it a "easier" way,you run a big risk of the chain moving 1 tooth off on the crank gear and you wouldn't even know it.Don't half ass it and hurt your motor more when your trying to fix it.

Tundraboarder666

Or just remove one and replace one at the same time. Should be okay doing it this way. Could always try it that way first and if it the chain jumps then retime the bitch.

rcarr0327

iTrader: (1)

How do you replace one at a time, only reason I'm shaking with touching the chain is because I've had problems before

1LowLS

You have to pull the cam to get to them.do it right or dont do it at all cause more damage. Trust me,i know.

07cobaltLScoupe

well looks like i need a new axle, my "temporary" fix is no more. got my alignment done but now this, like wtf? my cobalt turns 5 years old and **** just starts hitting the fan, with only 34k miles too. it's just irritating

1LowLS

**** happens dude.Especially when you mod.I've had a busted boot for a while,and this is with over 200whp.I'll wait for it to make noise lol.clickity clickity click.

Brags

Ive found our axels to be especially stout, f23 tranny too. Most of ours are holding up better than lsj axels, and f35s. I had a rip in my boot, Matty O rvt'd it no problem, put zzps in for two weeks while ordered new boot(kinda pain in the ass to replace boot), passenger side didn't last a week. After new boot came in put it on and stock axels back in (65000 miles) and its holding great. NO problems even spinning thru 1,2,3 consecutively. And im at 341 whp daily and saw 400+ with dave from pwerks on dyno

07cobaltLScoupe

yea i actually picked up a new tube of rtv silicone today and i'm gonna try that tomorrow after work and see how that holds before i order a new axle. i'm just not sure how it's gonna hold since it's right at a seem in the boot. but atleast if i need to replace the axle a guy i work with has a lift and said he'd help if i get him a case of beer i just hate the grease flying everywhere and on the back of my wheel