Official Base Model Thread
#1676
i know you can make the cams fit it takes some knocking and shaving lol i think idk i have talked to someone on here about it before honestly i want to stick with a blower thats my main thing but i want to be puttin down serious power so cams seemed like a good option basically i want to put more than 300 down at the wheels with a blower and no nitrous never been a fan of it so any other suggestions than a cam?
#1677
Senior Member
good luck with the M62.Your gonna need all of the cooling mods plus meth or run E85.Plus porting full bolt ons and alot of timing!!!Now with a turbo it's more possible.Im on the M62 with a 2.9 and full bolt ons with E85 and probably around 250ish whp.Its tough to get at/above 300whp because this blower generates alot of heat and doesnt flow nearly as much as a turbo would.
#1678
Senior Member
#1685
Well im gonna start with an m62 kit from zzp because it comes with everything i need and its affordable for now eventually ill probly switch to a tvs blower and i will DEFINATLEY be running meth by the end and a good H/E and i would love E cus its easy to access around my parts but i dont know how to do that setup but even at that if im runnin say a 2.8" pulley and meth on a good tune i think i will be close to 250-270 but not over thats my thought but im for sure not an expert at this im a painter not a wrench turner im just trying to figure this out as I go which is why Im askin all these questions. And i know that the power potential with a turbo is higher but thats kinda why i want a blower not that turbos arent great because they are but thats what almost everyone does for big numbers. i want to be a little different and have a high output from a blower (not that no one has done that either some guy on here almost hit 11's last weekend on a blower). Any ways if i had a tvs port and polished 2.7" pulley full bolt ons meth a good tune and supporting internals what do you think ill be puttin down just trying to figure out what my best route is going to be and you all are my experts.
#1690
And also said that im eventually going to go tvs
Last edited by Big_Red; 11-16-2011 at 04:45 PM. Reason: Automerged Doublepost
#1691
Senior Member
TVS youll need a built bottom end or your gonna go boom bottom end .Built bottom end,tvs,and e85 will put you over 300whp easy.
SC 2.2"s,Did you cut the intake manifold gasket in the middle for the PCV port since there offset?
SC 2.2"s,Did you cut the intake manifold gasket in the middle for the PCV port since there offset?
Last edited by 1LowLS; 11-16-2011 at 06:20 PM.
#1693
what all goes in to building up a bottom end and to run e??? like i said im a painter thank you by the way for reading the whole post to effectively answer my question 1lowls how small a pulley do you think i would want to run?
#1694
Senior Member
I'm not sure about pulley size on the TVS.Maybe ask a LSJ TVS guy or even Stenguyen.He's a built 2.2 on a tvs.Bottom end build would be forged rods/pistons and I would do arp headstuds as well.You can leave the sleeve's alone as there good to 400 but if you wanna exceed that then the block would have to go to a machine shop for some new sleeves.and to run E85,all you would need is 80 lbs injectors.If you do a M62 setup on a 2.9,you can run a 50/50 blend of E85 and 91 octane(or 93 if avail.)with 60 lbs injectors.but I would get 80's since you plan on a build with TVS.
#1699
@1lowls thanks for the help man made my day to get your expertise!!!!!
I got **** on all day and it will continue for the next 3 weeks by my boss cus i told him i was quiting. Got a 4 dollar an hour pay raise though in a new position so mods will be piling on alot faster HELL YES!
I got **** on all day and it will continue for the next 3 weeks by my boss cus i told him i was quiting. Got a 4 dollar an hour pay raise though in a new position so mods will be piling on alot faster HELL YES!
#1700
by the way if any one has pics of a cobalt on sparco drifts and wants to hook a brother up post em
pretty sure im goin with those in gloss black 16's cus i dont want low pro's
pretty sure im goin with those in gloss black 16's cus i dont want low pro's