Arizona BS Thread
Senior Member
iTrader: (1)
Join Date: 08-03-09
Location: North Phoenix
Posts: 5,110
Likes: 0
Received 0 Likes
on
0 Posts
Pictures from the Undie Run are soon to come! All 73MB worth
Overall it was a fun experience, smuggled in like 10 miniature smirnoffs and kept spiking my Fuze Drinks! Buddy lost his phone, we wondered around ASU in our underwear for about an hour with no luck locating it (He had GPS security on it, but they kept moving)
Overall it was a fun experience, smuggled in like 10 miniature smirnoffs and kept spiking my Fuze Drinks! Buddy lost his phone, we wondered around ASU in our underwear for about an hour with no luck locating it (He had GPS security on it, but they kept moving)
Senior Member
iTrader: (1)
Join Date: 02-03-09
Location: Phoenix, Arizona
Posts: 4,881
Likes: 0
Received 0 Likes
on
0 Posts
Undie run looked like a success lol
Bobbito I'm on ssc springs but one side sits higher than the.other so I can't do that to you haha and eh yeah I've had them off since then just gotta jack the rear up enough and they will slip out
Bobbito I'm on ssc springs but one side sits higher than the.other so I can't do that to you haha and eh yeah I've had them off since then just gotta jack the rear up enough and they will slip out
Senior Member
Join Date: 01-15-10
Location: M town AZ
Posts: 1,942
Likes: 0
Received 0 Likes
on
0 Posts
You tolling with stock springs in the rear?
Senior Member
Join Date: 10-08-06
Location: Scottsdale, AZ
Posts: 3,043
Likes: 0
Received 0 Likes
on
0 Posts
Senior Member
Join Date: 10-08-06
Location: Scottsdale, AZ
Posts: 3,043
Likes: 0
Received 0 Likes
on
0 Posts
so ive got the turbo all bolted in and the car is loud as hell. been data logginh for a couple days and all i could get is 16psi out of the turbo and it wouldnt spool till 5k rpm i also popped a lean at idle code. been talking with term these past couple of days trying to figure this thing out and he said i have a leak somewhere so i checked everything over was wondering if i had the wastegate setup right so i got on turbosmart's website looking at the intructions because i got this used and a parts list popped up and i saw that there was a valve seat that was suppose to go on the end of the plunger in the WG called them up yesterday and told the rep what was going on. he said that without the valve seat on that there is a 5mm gap all around the plunger and it will not seal and cause a major exhaust leak and i wouldnt be able to build boost. i told him i was ablt to build 16psi from 5k to 8k and it held he said that must be one hell of a turbo to do that even with a bad leak lol. so that cardalino guy shorted me a part ordering it today. hope this is the last thing and i can finally see what this thing can do
New Member
iTrader: (1)
Join Date: 12-21-09
Location: Arizona, Peoria
Posts: 186
Likes: 0
Received 0 Likes
on
0 Posts
Senior Member
iTrader: (1)
Join Date: 02-03-09
Location: Phoenix, Arizona
Posts: 4,881
Likes: 0
Received 0 Likes
on
0 Posts
Bobbito they arent stock they are ssc springs lol
Damn nick! I missed your call yesterday and forgot to call back super busy day, that sucks he shorted you that part but at least you know what the issue is charge that **** whatever you have to pay!
Damn nick! I missed your call yesterday and forgot to call back super busy day, that sucks he shorted you that part but at least you know what the issue is charge that **** whatever you have to pay!
Senior Member
Join Date: 01-15-10
Location: M town AZ
Posts: 1,942
Likes: 0
Received 0 Likes
on
0 Posts
Post a pic bruhh! I think mine sits the same lol are car look pretty close
Senior Member
iTrader: (1)
Join Date: 08-03-09
Location: North Phoenix
Posts: 5,110
Likes: 0
Received 0 Likes
on
0 Posts
so ive got the turbo all bolted in and the car is loud as hell. been data logginh for a couple days and all i could get is 16psi out of the turbo and it wouldnt spool till 5k rpm i also popped a lean at idle code. been talking with term these past couple of days trying to figure this thing out and he said i have a leak somewhere so i checked everything over was wondering if i had the wastegate setup right so i got on turbosmart's website looking at the intructions because i got this used and a parts list popped up and i saw that there was a valve seat that was suppose to go on the end of the plunger in the WG called them up yesterday and told the rep what was going on. he said that without the valve seat on that there is a 5mm gap all around the plunger and it will not seal and cause a major exhaust leak and i wouldnt be able to build boost. i told him i was ablt to build 16psi from 5k to 8k and it held he said that must be one hell of a turbo to do that even with a bad leak lol. so that cardalino guy shorted me a part ordering it today. hope this is the last thing and i can finally see what this thing can do
We can find out
Last edited by 08ssedan; 05-04-2011 at 01:26 PM. Reason: Automerged Doublepost
Senior Member
Join Date: 10-08-06
Location: Scottsdale, AZ
Posts: 3,043
Likes: 0
Received 0 Likes
on
0 Posts
let me know what you wanna do i live right by you
Senior Member
iTrader: (1)
Join Date: 08-03-09
Location: North Phoenix
Posts: 5,110
Likes: 0
Received 0 Likes
on
0 Posts