SCcobaltSS

iTrader: (2)

Yes you should have a good starting point. Tyler needs to get the key, bolt, and pulley right away. Wait time on that stuff will be your break! haha

1LowLS

we still have the stock balancer.so just the key and bolt is needed.

SCcobaltSS

iTrader: (2)

Word! The key took a couple days for me to get from the dealer.

evofire

ill make calls right now. think they will know what i mean when i say crank key?

SCcobaltSS

iTrader: (2)

Yes, they will (I hope).. I called it a woodruff key and they didnt know..

evofire

lol...Andy at Thoroughbred should know...hes the ****!

evofire

Both parts are in stock at Brown and Brown Chevy in Mesa.

Bolt 11589123 $6.32
Key 24424855 $5.59

Pulled off the shelf under Tylers names. They close at 7.

Brown and Brown Chevrolet
145 E. Main Street
Mesa, Arizona
85201

SCcobaltSS

iTrader: (2)

Nice! Surprised they had them! but when I go to other dealers they typically say Brown and Brown has it.

evofire

I called Thoroughbred. They told me Brown and Brown had them...lol

SCcobaltSS

iTrader: (2)

Good ol' Brown and Brown

evofire

Torque Specs for new bolt.

-Crankshaft pulley bolt
First pass ……………………...............………100 N-m / 74 lb ft
Second pass …………………..............………75 degrees

SCcobaltSS

iTrader: (2)

I belileve its 76 ft. lbs and a 125* twist.

I dont think the cranks are that much different than the LSJ and that is what I used.

I think that degree **** is crap. JUST SAY 100 LB FT AND BE DONE WITH IT... *******.

evofire

lol. i got that info from the jbody l61. same crank different reluctor wheel. so whatev...lol

SCcobaltSS

iTrader: (2)

I see. Well those are my numbers and I am sticking with them! haha

I am almost certain its 125* That has to make it like 125ft lbs total.. That is a larger twist.

When you fix his car you should do as stated then take the trq wrench to 100 ft lbs and go up about 2 ft lbs until it rotates the bolt a little and figure out the actual number..

This will help me when I do my seals and lash's becasue I will retime

evofire

will do. my wrench will do 1 ft/lb at a time. so we will see. if we snap the bolt u get to fix it....lol

SCcobaltSS

iTrader: (2)

You wont snap it becasue you go in increments. It will click and you stop at that ft. lb.

-Disclaimer-
If crank pulley bolt is tightened and snap bolt I, Chris, am not responsible for this error and will not come to fix mistake.
-End of Disclaimer-



Besides there is always a tolerance with the ft.lbs + * twist by about +/-4* or something. You should be good.

1LowLS

Word.Look what I found in my front yard.I wanna race em.Apparently road runners are not afraid of people.He let me get right next to him before I grabbed the camera lol
http://www.flickr.com/photos/fastl61/6261369937/http://www.flickr.com/photos/fastl61/6261369937/ by http://www.flickr.com/people/fastl61/, on Flickr

CrateEngineDepot

iTrader: (5)

Going to be away from my pc for a hour but anything going on this evening?

1LowLS

Nope.not tonight.Nothing I can think of anyway lol

08ssedan

iTrader: (1)

You guys are too far away to do anything anyways lol

1LowLS

your the one far away.were all within a 20 minute drive of each other lol.

evofire

word!

1LowLS

bored

evofire

sleepy

1LowLS

derp